How is cantilever rack different from pallet rack?

Pallet rack has a front beam and stores discrete, boxed loads. Cantilever has an open front, so long material loads from the side and slides in without clearing an obstruction - that's the entire reason the system exists.

How far apart should the columns be?

Close enough that the load doesn't sag between arms. A common starting point puts arm spacing at roughly half the load length, with the remainder overhanging each end evenly. We check that math against your heaviest bundle before finalizing spacing.

Straight arms or inclined arms?

Straight arms suit boxed, banded, or sheet goods. Inclined arms, usually fitted with a lip, keep pipe, tube, and round stock from rolling forward off the arm. Many runs mix both across different levels.

Can arms or levels be added later?

Yes. Arms mount at set increments up the column, so levels can be added or repositioned as your product mix shifts, as long as total load stays within the rated capacity of the column and base.

Can we add more lanes or positions later without redoing the whole system?

That is the point of designing it as a layout rather than a one-off order. We keep the drawing on file, so adding a bay, a lane, or a run next year starts from where the system already is instead of from scratch.

What does a cantilever rack project in Coral Springs typically cost per pallet position?

It depends on beam capacity, height, and how deep you store, which is why the quote is itemized and the layout shows a position count. Comparing cost per position across two configurations on your own floor plan is the only honest way to answer it.

Cantilever Rack system inside a Florida warehouse

Coral Springs, Florida

Cantilever Rack Layouts for Coral Springs, FL

Name: Miami Warehouse Racking
Address: 1738 SW 57th Ave., Miami, FL, 33155, US
Telephone: (305) 930-7780
Price range: $$

Warehouse rent climbing faster than the floor plan can keep up with shows up constantly in Sample Road corridor facilities. Adding cantilever rack is how a Coral Springs operation gets capacity back without paying for square footage it already has.

With arm length and capacity set by the bundles you handle on the table, the consumer brands operations we work with near NW 15th Street industrial usually want cost per pallet position, not a lump sum. That is what the cantilever rack layout and itemized quote for a NW 15th Street industrial building show. Call (305) 930-7780 to start one for Coral Springs.

(305) 930-7780

Why Coral Springs Warehouses Work With Us

No two buildings near Corporate Park carry the same combination of clear height, aisle width, and floor loading, which is why we draw every Coral Springs layout to the site instead of pulling one off a shelf.

We have been laying out cantilever rack for medical devices and consumer brands operations in the Coral Springs market as part of Warehouse Equipment & Supplies Co. since 1997, and single-sided runs along the wall, double-sided in open floor is the cantilever rack fit question we work through with your Coral Springs team before quoting.

And you deal with one team throughout — cantilever rack layout, pricing, delivery windows into Corporate Park, installation scheduling, and parts after the fact. Nothing about the Coral Springs job gets handed to a call center.

Free warehouse consultation

CAD layout with position counts

Installation by trusted installation partners

Operations We Rack Around Here

Nearby areas we work in regularly include Corporate Park, NW 15th Street industrial, Sample Road corridor, Coral Springs flex district.

Medical devices

Consumer brands

Light assembly

E-commerce fulfillment

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

How Cantilever Rack Works

Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.

Columns and anchored bases

Upright columns sit on bases anchored to the slab. Base depth is set by load and arm length so the run stays stable even under an off-center pick.

Arms at adjustable heights

Arms bolt or pin into the column at set increments and move as your product mix changes. Straight arms suit boxed goods; inclined arms with a lip hold round or loose stock in place.

Column spacing against sag

Spacing between columns is set so bundles don't sag between arms. A common starting rule places arms about half the load length apart, with the ends overhanging evenly.

Single-sided or double-sided

Single-sided runs go against a wall. Double-sided runs stand in open floor and load from both faces, doubling capacity per base without doubling the footprint.

What a Cantilever Rack Project Includes

Before cantilever rack is priced for a NW 15th Street industrial site, we collect the constraints: usable height, column grid, aisle widths your lifts need, and the pallet mix your consumer brands volume actually moves.

You then get a cantilever rack position count for the Coral Springs footprint, load ratings for every beam level, and pricing broken out by component, so cost per pallet position is visible rather than buried in a lump sum. Where it makes sense we run the same plan a second way, with single-sided runs along the wall, double-sided in open floor.

Cantilever Rack delivery into Coral Springs is coordinated around your schedule, and installation partners build to the approved drawing, anchor every frame, and confirm the system performs loaded before turning it over. The job is phased so your Coral Springs operation keeps running, and teardown, reconfiguration, or adding a lane later is handled by the same team.

Lumber, plywood, and sheet goods

Pipe, tube, conduit, and bar stock

Steel service center inventory

Furniture, doors, and windows

Long or awkward loads currently sitting on the floor

Call (305) 930-7780

Recent Installations

Racking projects completed for warehouses across South Florida.

View More Projects

Get a Cantilever Rack Quote for Your Coral Springs Warehouse

Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (305) 930-7780.

Miami Warehouse Racking

1738 SW 57th Ave.

Unit #A559

Miami, FL 33155

(305) 930-7780

Monday - Friday: 8:00 AM - 6:00 PM

Name *

Company *

Email *

Phone *

Where are you located? *

Approximate warehouse size *

Expected timeframe *

Additional Information

I consent to receive SMS and email communications from Miami Warehouse Racking regarding my quote request. Message and data rates may apply. Reply STOP to opt out.

We respect your privacy. Your information will never be shared.

Cantilever Rack Questions We Hear Most

Other Rack Types We Supply in Coral Springs

Pallet Rack

Every pallet reachable, every time. The baseline we size everything else against.

View details

Pushback Rack

Two to six pallets deep from one aisle, without giving up much reach.

View details

Pallet Flow Rack

Load one side, pick the other, and let gravity enforce first in, first out.

View details

Drive-In Rack

No aisles. The forklift enters the structure, and the floor holds more pallets per square foot than any other system.

View details

Carton Flow Rack

Cases advance to the picker instead of the picker hunting for cases.

View details

Nearby Areas We Also Serve

Our delivery and installation territory covers Miami-Dade, Broward, and Palm Beach counties, so one team can handle multiple buildings for the same company.

Cantilever Rack in Miami Cantilever Rack in Fort Lauderdale Cantilever Rack in Hialeah Cantilever Rack in Doral Cantilever Rack in Medley Cantilever Rack in Pompano Beach

View All Service Areas

Where We Work

Located in Miami, we serve the entire South Florida region with industrial pallet racks and warehouse storage solutions.

Miami Warehouse Racking

Address

1738 SW 57th Ave.
Unit #A559
Miami, FL 33155

Phone

(305) 930-7780

Business Hours

Monday - Friday: 8:00 AM - 6:00 PM
Saturday: Closed
Sunday: Closed

Need Cantilever Rack in Coral Springs?

Call (305) 930-7780 or request a quote and we will get a layout started.

(305) 930-7780